how to level a washing machine under a counter

Ensure the lock nuts on the feet are tight against the bottom of the cabinet. Measure from the laser line to the four points where the feet of the washing machine will rest on the floor.

22 Small Laundry Room Ideas Tiny But Mighty Designs Real Homes

This will help you know which areas to start with.

. Washerdryer pairs average 75 inches tall when stacked leaving just 11 inches of space above them in a room with an 8-foot ceiling. Mark each pad location on the floor. Leveling a washing machine is essential for proper operation.

Be sure to mark the areas that are not level. Start by lifting each corner of the machine and slipping a pad under each foot. Disconnect it firstand pull it out from underneath the counter.

To set the rear self-leveling system tip the machine forward so that the rear legs are about 4 off the floor. Next get your helper or helpers to carefully lift your machine onto a dolly. WM only has to be lifted a fraction to free feet up so you can adjust them.

Turn the feet either clockwise to lower the feet or counter clockwise to raise the feet. By screwing the one leg all the way in to avoid vibration you can then adjust the other as needed until the washer sits flat. Measure the length and width of the washing machine with a tape measure and cut a rectangular piece of 58-inch plywood with a circular saw that.

Watch a video below for instruction on leveling the washer. Confirm with your level tool before you carry on. Turn the feet either clockwise to lower the feet or counter clockwise to raise the feet.

Use a 38 wrench to tighten both jam nuts securely against the base of the washer. They should bend their legs to get into position. Now subtract that height from the other points and record that.

When the bubble of the level centers itself perfectthen the machine is level. To do this break out your bubble level and check for level by placing it side to side then by checking front to back. Tilt the washing machine backward so the front legs are exposed.

Also be careful that you dont tip the machine so much that any connections to hoses or cables are stressed. Washing machines are leveled through the small often unnoticed feet on the bottom of the machine. If the appliance still isnt level you will need to readjust the leg or legs accordingly.

Leveling the Washing Machine. As hallbeck says use level on front of wm - sellotape the level to the front of the machine top of level aligned with something horizontal on the machine like the bottom edge of the machines top. Use a 2 x 4 piece of wood under the front to support the legs.

To tighten the jam nut turn counter-clockwise to loosen turn clockwise. Get someone to help you while youre doing this as you wont be able to hold the machine in place and also perform the next steps. Then lift the washer out of the way so you can apply the adhesive discs and mount the pads to the floor as shown.

How to Level A Washing Machine. Use the bubble level to confirm the washer is now level side-to-side and front-to-back with all four feet firmly in contact with the floor. The self-leveling legs will automatically adjust.

Hold the blankets in place with a cord or packing tape. How to level a washing machine on an uneven floor is straightforward you can loosen the lock nut on each of the two front legs. Both people should place one hand inside the machine and press it against the top.

WM feet are usually easy to adjust in situ - especially front ones. Remove the support and carefully set the washer on the floor. Start with a laser level projecting a line across the full width of the opening.

Keep the machine upright as you wheel it through and out of the house. Now under the washing machine are four adjustable pedestals scew them either up or downwith a carpenters level on top of the machine. The shortest measurement will be your starting or zero point.

Secure the washer to the dolly with ropes. Support the front of the machine. They should place the other hand against the back of the machine.

Tilt the washer forward so that the back of the machine rises about 6 inches from the floor and then gently lower the washer back into position. Side-by-side washerdryer pairs stand 33 inches tall and need another 24 inches of clearance for a top-loading washer leaving 39 inches above the washer for a cabinet.

Laundry Room Makeover Ideas